Search Results

Search found 28439 results on 1138 pages for '9 10'.

Page 859/1138 | < Previous Page | 855 856 857 858 859 860 861 862 863 864 865 866  | Next Page >

• ghettoVCB issue

  - by romgo75

  I have setup a ghettoVCB script in order to backup three VM. I put it in a crontab but I have an issue. In my backup folder I have 3 different folders, one for each VM. In each folder I have the following files: -rw-r--r-- 1 root root 1263 Mar 17 01:51 vm1-2010-03-16--2.gz -rw-r--r-- 1 root root 1263 Mar 17 00:41 vm1-2010-03-16--3.gz -rw-r--r-- 1 root root 1261 Mar 18 01:22 vm1-2010-03-17--1.gz drwxr-xr-x 1 root root 980 Mar 19 23:39 vm1-2010-03-19 The problem is the last folder. It seems that a backup didn't finish the process. When I read the logs concerning this folder I get: 2010-03-19 23:00:01 -- info: CONFIG - VM_BACKUP_VOLUME = /vmfs/volumes/datastore1/backup/ 2010-03-19 23:00:01 -- info: CONFIG - VM_BACKUP_ROTATION_COUNT = 3 2010-03-19 23:00:01 -- info: CONFIG - DISK_BACKUP_FORMAT = zeroedthick 2010-03-19 23:00:01 -- info: CONFIG - ADAPTER_FORMAT = buslogic 2010-03-19 23:00:01 -- info: CONFIG - POWER_VM_DOWN_BEFORE_BACKUP = 0 2010-03-19 23:00:01 -- info: CONFIG - ENABLE_HARD_POWER_OFF = 0 2010-03-19 23:00:01 -- info: CONFIG - ITER_TO_WAIT_SHUTDOWN = 3 2010-03-19 23:00:01 -- info: CONFIG - POWER_DOWN_TIMEOUT = 5 2010-03-19 23:00:01 -- info: CONFIG - SNAPSHOT_TIMEOUT = 15 2010-03-19 23:00:01 -- info: CONFIG - LOG_LEVEL = info 2010-03-19 23:00:01 -- info: CONFIG - BACKUP_LOG_OUTPUT = stdout 2010-03-19 23:00:01 -- info: CONFIG - VM_SNAPSHOT_MEMORY = 0 2010-03-19 23:00:01 -- info: CONFIG - VM_SNAPSHOT_QUIESCE = 0 2010-03-19 23:00:01 -- info: CONFIG - VMDK_FILES_TO_BACKUP = all http://... 2010-03-19 23:39:35 -- info: Initiate backup for vm1 2010-03-19 23:39:35 -- info: Creating Snapshot "ghettoVCB-snapshot-2010-03-19" for vm1 Destination disk format: VMFS zeroedthick Cloning disk '/vmfs/volumes/datastore1/vm1/vm1_1.vmdk'... ^MClone: 0% done.^MClone: 1% done.^MClone: 2% done.^MClone: 3% done.^MClone: 4% done.^MClone: 5% done.^MClone: 6% done.^MClone: 7% done.^MClone: 8% done.^MClone: 9% done.^MClone Failed to clone disk : The file already exists (39). Destination disk format: VMFS zeroedthick Cloning disk '/vmfs/volumes/datastore1/vm1/vm1.vmdk'... 2010-03-20 00:46:20 -- info: Removing snapshot from vm1 ... one: 7% done.^MClone: 8% done.^MClone: 9% done.^MClone: 10% done.^MClone: 11% done.^MClone: 12% done.^MClone: 13% done.^MClone: 14% done.^MClone: 15% done.^MClone: 16% done.^MCl 2010-03-19 23:51:19 -- info: Removing snapshot from vm1 ... I can't run ghettoVCB anymore because the VM has a snapshot which has not been deleted. I know how to delete the snapshot, but I don't know why the VCB script is not able to handle rotation of the VM backups? Any ideas? Thanks!

  Read the article

• PXE boot -- kernel not found on TFTP server

  - by user70523

  I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

  Read the article

• Migrating Windows XP BOOT.INI Settings to Windows 7 Boot-loader

  - by Synetech inc.

  Hi, Two months ago my motherboard died, so I bought a used computer that came with Windows 7. I have since installed my old hard-drive, which had Windows XP on it, in this system. What I am trying to do now is to figure out a way to migrate the settings from XP's BOOT.INI into 7's boot-loader. Below is the BOOT.INI I used in XP (I have reduced the strings and updated the disks to point to the new location of the old HD. Oh and I am not clear on the drive letters. In XP, I could boot the recovery console or MS-DOS from a file in C:\ that contains the boot-sector. I am not sure what drive letter it would be called now—I had to manually change all the drive letters of the old partitions in Windows 7 because it auto-assigned them all wrong/differently). [boot loader] timeout=10 default=multi(0)disk(0)rdisk(1)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP" /fastdetect multi(0)disk(0)rdisk(1)partition(1)\WINDOWS="XP (Safe)" /safeboot:network /sos /bootlog /noguiboot C:\CMDCONS\BOOTSECT.DAT="Recovery Console" /cmdcons C:\BOOTSECT.DOS="MS-DOS 7.10" /win95 I have looked around, and have only been able to find some bcdedit commands to add XP to the boot-loader, but none that include information on setting safe-mode for it (or changing any of the XP load options for that matter). Not surprisingly I suppose, I have not found anything on adding the XP recovery console or DOS to the Windows 7 boot-loader. (Yes, I tried EasyBCD, but that did not help; it had no options for XP, and the best I managed was to get a choice of booting 7 or normal-mode XP—choosing XP didn't even give the old XP boot menu.) Can anyone please tell me how to export the entries in XP's boot.ini to 7's boot-loader so that on boot, I can choose to load the following: Windows 7 Windows 7 (Safe-mode) (Windows 7 (The Win7 counterpart of the Recovery Console)) Windows XP Windows XP (Safe-mode) Windows XP (Recovery Console) MS-DOS 7.10

  Read the article

• GTX 280 purple snow on bootup, card works without drivers

  - by Brokar

  i have owned a ASUS GTX280 for 3 years now. The card has been great all along but i started having problems 10 days ago. I was playing Diablo 3 for 1 week on max settings no problems, then suddenly my display kept getting some weird purple/colours as soon as i booted and logged into windows. Went into safe mode, updated drivers and it kept crashing. Formatted PC, fresh windows install with new WHQL drivers again same problem. Uninstalled nvidia drivers and pc has been running great for 4 days now, ofcourse i cannot run games but everything works on 1680x1050 resolution and i can browse internet,watch movies and use my PC for everything but gaming. As soon as i install nvidia drivers PC won't boot. I only wanna game a few hours a week (very busy program with school this month so it might be a blessing that i cannot game) and i would love it if i could keep the card. I am looking to upgrde later on when i will have time for gaming but i wonder if i could still use the card somehow with different/new drivers (tried older drivers that came with the card on a CD aswell) tldr: PC works fine with no nvidia drivers (apart from gaming ofc). Once i install WHQL drivers or older ones, cannot even log into windows. Fix?

  Read the article

• Kernel panic while loading Mac OS X on VMWare

  - by Vladimir Gritsenko

  I'm trying to run Mac OS X 10.6.3 on VMWare 7.1 from within Windows 7 64 bit. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

  Read the article

• Finding out why Dell Controler is Degraded

  - by Kyle Brandt

  I installed open manage on a couple of my PE 2950s for snmp monitoring of the RAID. All the checks seem to come back okay except for controllerState: [root@aMachine ~]# snmpwalk -v 2c -c bestNotToPostPasswords myMachine -m +StorageManagement-MIB controllerstate StorageManagement-MIB::controllerState.1 = INTEGER: degraded(6) Other checks seems to indicate the battery, LD, and physicals disks are all good unless I missing something. Can anyone tell if I am missing something or neglecting something import in my RAID monitoring/understanding? I get degraded for both these servers I have set up. A walk of the entire storage management tree for on of them: StorageManagement-MIB::softwareVersion.0 = STRING: "3.2.0" StorageManagement-MIB::globalStatus.0 = INTEGER: warning(2) StorageManagement-MIB::softwareManufacturer.0 = STRING: "Dell Inc." StorageManagement-MIB::softwareProduct.0 = STRING: "Server Administrator (Storage Management)" StorageManagement-MIB::softwareDescription.0 = STRING: "Configuration and monitoring of disk storage devices." StorageManagement-MIB::displayName.0 = STRING: "Server Administrator (Storage Management)" StorageManagement-MIB::description.0 = STRING: "Configuration and monitoring of disk storage devices." StorageManagement-MIB::agentVendor.0 = STRING: "Dell Inc." StorageManagement-MIB::agentTimeStamp.0 = INTEGER: 1273842310 StorageManagement-MIB::agentGetTimeout.0 = INTEGER: 5 StorageManagement-MIB::agentModifiers.0 = INTEGER: 0 StorageManagement-MIB::agentRefreshRate.0 = INTEGER: 300 StorageManagement-MIB::agentMibVersion.0 = STRING: "3.2" StorageManagement-MIB::agentManagementSoftwareURLName.0 = "" StorageManagement-MIB::agentGlobalSystemStatus.0 = INTEGER: nonCritical(4) StorageManagement-MIB::agentLastGlobalSystemStatus.0 = INTEGER: ok(3) StorageManagement-MIB::agentSmartThermalShutdown.0 = INTEGER: notApplicable(3) StorageManagement-MIB::controllerNumber.1 = INTEGER: 1 StorageManagement-MIB::controllerName.1 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::controllerVendor.1 = STRING: "DELL" StorageManagement-MIB::controllerType.1 = INTEGER: sas(6) StorageManagement-MIB::controllerState.1 = INTEGER: degraded(6) StorageManagement-MIB::controllerRebuildRateInPercent.1 = INTEGER: 30 StorageManagement-MIB::controllerFWVersion.1 = STRING: "5.0.2-0003" StorageManagement-MIB::controllerCacheSizeInMB.1 = INTEGER: 256 StorageManagement-MIB::controllerCacheSizeInBytes.1 = INTEGER: 0 StorageManagement-MIB::controllerPhysicalDeviceCount.1 = INTEGER: 5 StorageManagement-MIB::controllerLogicalDeviceCount.1 = INTEGER: 1 StorageManagement-MIB::controllerRollUpStatus.1 = INTEGER: nonCritical(4) StorageManagement-MIB::controllerComponentStatus.1 = INTEGER: nonCritical(4) StorageManagement-MIB::controllerNexusID.1 = STRING: "\\0" StorageManagement-MIB::controllerAlarmState.1 = INTEGER: disabled(2) StorageManagement-MIB::controllerDriverVersion.1 = STRING: "00.00.03.05 " StorageManagement-MIB::controllerPCISlot.1 = STRING: "embedded" StorageManagement-MIB::controllerClusterMode.1 = INTEGER: notApplicable(99) StorageManagement-MIB::controllerMinFWVersion.1 = STRING: "5.2.1-0067" StorageManagement-MIB::controllerMinDriverVersion.1 = STRING: "00.00.03.21" StorageManagement-MIB::controllerChannelCount.1 = INTEGER: 2 StorageManagement-MIB::controllerReconstructRate.1 = INTEGER: 30 StorageManagement-MIB::controllerPatrolReadRate.1 = INTEGER: 30 StorageManagement-MIB::controllerBGIRate.1 = INTEGER: 30 StorageManagement-MIB::controllerCheckConsistencyRate.1 = INTEGER: 30 StorageManagement-MIB::controllerPatrolReadMode.1 = INTEGER: automatic(1) StorageManagement-MIB::controllerPatrolReadState.1 = INTEGER: stopped(1) StorageManagement-MIB::controllerPatrolReadIterations.1 = INTEGER: 162 StorageManagement-MIB::controllerEntry.57.1 = INTEGER: 99 StorageManagement-MIB::controllerEntry.58.1 = INTEGER: 99 StorageManagement-MIB::channelNumber.1 = INTEGER: 1 StorageManagement-MIB::channelNumber.2 = INTEGER: 2 StorageManagement-MIB::channelName.1 = STRING: "Connector 0" StorageManagement-MIB::channelName.2 = STRING: "Connector 1" StorageManagement-MIB::channelState.1 = INTEGER: ready(1) StorageManagement-MIB::channelState.2 = INTEGER: ready(1) StorageManagement-MIB::channelRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::channelRollUpStatus.2 = INTEGER: ok(3) StorageManagement-MIB::channelComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::channelComponentStatus.2 = INTEGER: ok(3) StorageManagement-MIB::channelNexusID.1 = STRING: "\\0\\0" StorageManagement-MIB::channelNexusID.2 = STRING: "\\0\\1" StorageManagement-MIB::channelBusType.1 = INTEGER: sas(8) StorageManagement-MIB::channelBusType.2 = INTEGER: sas(8) StorageManagement-MIB::enclosureNumber.1 = INTEGER: 1 StorageManagement-MIB::enclosureName.1 = STRING: "Backplane" StorageManagement-MIB::enclosureVendor.1 = STRING: "DELL" StorageManagement-MIB::enclosureState.1 = INTEGER: ready(1) StorageManagement-MIB::enclosureProductID.1 = STRING: "BACKPLANE " StorageManagement-MIB::enclosureType.1 = INTEGER: internal(1) StorageManagement-MIB::enclosureChannelNumber.1 = INTEGER: 0 StorageManagement-MIB::enclosureRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::enclosureComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::enclosureNexusID.1 = STRING: "\\0\\0\\0" StorageManagement-MIB::enclosureFirmwareVersion.1 = STRING: "1.00" StorageManagement-MIB::enclosureSASAddress.1 = STRING: "50019090B4C67200" StorageManagement-MIB::arrayDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskName.1 = STRING: "Physical Disk 0:0:0" StorageManagement-MIB::arrayDiskName.2 = STRING: "Physical Disk 0:0:1" StorageManagement-MIB::arrayDiskName.3 = STRING: "Physical Disk 0:0:2" StorageManagement-MIB::arrayDiskName.4 = STRING: "Physical Disk 0:0:3" StorageManagement-MIB::arrayDiskVendor.1 = STRING: "DELL " StorageManagement-MIB::arrayDiskVendor.2 = STRING: "DELL " StorageManagement-MIB::arrayDiskVendor.3 = STRING: "DELL " StorageManagement-MIB::arrayDiskVendor.4 = STRING: "DELL " StorageManagement-MIB::arrayDiskState.1 = INTEGER: online(3) StorageManagement-MIB::arrayDiskState.2 = INTEGER: online(3) StorageManagement-MIB::arrayDiskState.3 = INTEGER: online(3) StorageManagement-MIB::arrayDiskState.4 = INTEGER: online(3) StorageManagement-MIB::arrayDiskProductID.1 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskProductID.2 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskProductID.3 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskProductID.4 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskSerialNo.1 = STRING: "3LN0LRL0 " StorageManagement-MIB::arrayDiskSerialNo.2 = STRING: "3LN0JYJS " StorageManagement-MIB::arrayDiskSerialNo.3 = STRING: "3LN0LR0V " StorageManagement-MIB::arrayDiskSerialNo.4 = STRING: "3LN0JH97 " StorageManagement-MIB::arrayDiskRevision.1 = STRING: "T106" StorageManagement-MIB::arrayDiskRevision.2 = STRING: "T106" StorageManagement-MIB::arrayDiskRevision.3 = STRING: "T106" StorageManagement-MIB::arrayDiskRevision.4 = STRING: "T106" StorageManagement-MIB::arrayDiskEnclosureID.1 = STRING: "0" StorageManagement-MIB::arrayDiskEnclosureID.2 = STRING: "0" StorageManagement-MIB::arrayDiskEnclosureID.3 = STRING: "0" StorageManagement-MIB::arrayDiskEnclosureID.4 = STRING: "0" StorageManagement-MIB::arrayDiskChannel.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskChannel.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskChannel.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskChannel.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInMB.1 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInMB.2 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInMB.3 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInMB.4 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskTargetID.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskTargetID.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskTargetID.3 = INTEGER: 2 StorageManagement-MIB::arrayDiskTargetID.4 = INTEGER: 3 StorageManagement-MIB::arrayDiskLunID.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLunID.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLunID.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLunID.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInMB.1 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInMB.2 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInMB.3 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInMB.4 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskBusType.1 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskBusType.2 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskBusType.3 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskBusType.4 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskSpareState.1 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskSpareState.2 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskSpareState.3 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskSpareState.4 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskRollUpStatus.2 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskRollUpStatus.3 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskRollUpStatus.4 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.2 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.3 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.4 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskNexusID.1 = STRING: "\\0\\0\\0\\0" StorageManagement-MIB::arrayDiskNexusID.2 = STRING: "\\0\\0\\0\\1" StorageManagement-MIB::arrayDiskNexusID.3 = STRING: "\\0\\0\\0\\2" StorageManagement-MIB::arrayDiskNexusID.4 = STRING: "\\0\\0\\0\\3" StorageManagement-MIB::arrayDiskPartNumber.1 = STRING: "SG0DR2381253172FLRL0A00 " StorageManagement-MIB::arrayDiskPartNumber.2 = STRING: "SG0DR2381253172FJYJSA00 " StorageManagement-MIB::arrayDiskPartNumber.3 = STRING: "SG0DR2381253172FLR0VA00 " StorageManagement-MIB::arrayDiskPartNumber.4 = STRING: "SG0DR2381253172FJH97A00 " StorageManagement-MIB::arrayDiskSASAddress.1 = STRING: "5000C50002380201" StorageManagement-MIB::arrayDiskSASAddress.2 = STRING: "5000C50002385B89" StorageManagement-MIB::arrayDiskSASAddress.3 = STRING: "5000C50002385AA9" StorageManagement-MIB::arrayDiskSASAddress.4 = STRING: "5000C500023841E1" StorageManagement-MIB::arrayDiskSmartAlertIndication.1 = INTEGER: no(1) StorageManagement-MIB::arrayDiskSmartAlertIndication.2 = INTEGER: no(1) StorageManagement-MIB::arrayDiskSmartAlertIndication.3 = INTEGER: no(1) StorageManagement-MIB::arrayDiskSmartAlertIndication.4 = INTEGER: no(1) StorageManagement-MIB::arrayDiskManufactureDay.1 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureDay.2 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureDay.3 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureDay.4 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.1 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.2 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.3 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.4 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureYear.1 = STRING: "2005" StorageManagement-MIB::arrayDiskManufactureYear.2 = STRING: "2005" StorageManagement-MIB::arrayDiskManufactureYear.3 = STRING: "2005" StorageManagement-MIB::arrayDiskManufactureYear.4 = STRING: "2005" StorageManagement-MIB::arrayDiskMediaType.1 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskMediaType.2 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskMediaType.3 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskMediaType.4 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskEntry.36.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.36.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.36.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.36.4 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.40.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.40.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.40.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.40.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.1 = STRING: "Physical Disk 0:0:0" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.2 = STRING: "Physical Disk 0:0:1" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.3 = STRING: "Physical Disk 0:0:2" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.4 = STRING: "Physical Disk 0:0:3" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.1 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.2 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.3 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.4 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.4 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.1 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.2 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.3 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.4 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.4 = INTEGER: 1 StorageManagement-MIB::batteryNumber.1 = INTEGER: 1 StorageManagement-MIB::batteryName.1 = STRING: "Battery 0" StorageManagement-MIB::batteryVendor.1 = STRING: "DELL" StorageManagement-MIB::batteryState.1 = INTEGER: ready(1) StorageManagement-MIB::batteryRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::batteryComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::batteryNexusID.1 = STRING: "\\0\\0" StorageManagement-MIB::batteryPredictedCapacity.1 = INTEGER: ready(2) StorageManagement-MIB::batteryNextLearnTime.1 = INTEGER: 21 StorageManagement-MIB::batteryLearnState.1 = INTEGER: idle(16) StorageManagement-MIB::batteryEntry.13.1 = INTEGER: 0 StorageManagement-MIB::batteryMaxLearnDelay.1 = INTEGER: 168 StorageManagement-MIB::batteryConnectionNumber.1 = INTEGER: 1 StorageManagement-MIB::batteryConnectionBatteryName.1 = STRING: "Battery 0" StorageManagement-MIB::batteryConnectionBatteryNumber.1 = INTEGER: 1 StorageManagement-MIB::batteryConnectionControllerName.1 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::batteryConnectionControllerNumber.1 = INTEGER: 1 StorageManagement-MIB::virtualDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::virtualDiskName.1 = STRING: "Virtual Disk 0" StorageManagement-MIB::virtualDiskDeviceName.1 = STRING: "/dev/sda" StorageManagement-MIB::virtualDiskState.1 = INTEGER: ready(1) StorageManagement-MIB::virtualDiskLengthInMB.1 = INTEGER: 278784 StorageManagement-MIB::virtualDiskLengthInBytes.1 = INTEGER: 0 StorageManagement-MIB::virtualDiskWritePolicy.1 = INTEGER: writeBack(3) StorageManagement-MIB::virtualDiskReadPolicy.1 = INTEGER: noReadAhead(5) StorageManagement-MIB::virtualDiskCachePolicy.1 = INTEGER: not-applicable(99) StorageManagement-MIB::virtualDiskLayout.1 = INTEGER: raid-10(10) StorageManagement-MIB::virtualDiskCurStripeSizeInMB.1 = INTEGER: 0 StorageManagement-MIB::virtualDiskCurStripeSizeInBytes.1 = INTEGER: 65536 StorageManagement-MIB::virtualDiskTargetID.1 = INTEGER: 0 StorageManagement-MIB::virtualDiskRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::virtualDiskComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::virtualDiskNexusID.1 = STRING: "\\0\\0" StorageManagement-MIB::virtualDiskArrayDiskType.1 = INTEGER: sas(1) StorageManagement-MIB::virtualDiskEntry.23.1 = INTEGER: 2 StorageManagement-MIB::virtualDiskEntry.24.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.1 = STRING: "Physical Disk 0:0:0" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.2 = STRING: "Physical Disk 0:0:1" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.3 = STRING: "Physical Disk 0:0:2" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.4 = STRING: "Physical Disk 0:0:3" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.1 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.2 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.3 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.4 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.4 = INTEGER: 1

  Read the article

• Linksys WAP54G v3.1 no access, power and link LED solid

  - by user142113

  I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

  Read the article

• Trojan Horse Generic.15.apnz Virus Impossible to get rid of?!

  - by DaveDev

  Hi Guys I'm new to this forum so I'm unsure whether this is the right place for a question like this. I have a Trojan Horse infection that lives in memory and seems to be impossible to get rid of. I've tried a vew AntiVirus products (Norton, Windows Essentials & AVG Free) all to no avail & I've recently tried a few bootable antivirus solutions I found here: http://www.techmixer.com/free-bootable-antivirus-rescue-cds-download-list/ Kaspersky Rescue Disk 2008 (failed - it wouldn't even load the UI, is there a newer one out there?) F Secure Rescue Disk (Updates & Scanner ran, found 10 infections, said it was going to delete or repair them, but didn't get rid of them) Avira found a load of infections but it froze when I tried to interact with the UI after the scan. Every time I run these I'll load Windows after & run AVG, and it still finds Trojan Horse Generic.15.apnz (in Services.exe) & Trojan Horse Generic.16.ARSU (in svchost.exe) Is anyone familiar with a virus like this? Can anyone suggest how to approach a solution? Thanks Dave

  Read the article

• Increasing MSSQL/Sage performance with SSD? (Dell PE T410)

  - by Anthony

  I have a client wanting better performance of their Sage (Accpac & CRM) server (v5.5, soon to be v7). It's running on 1 of 2 Hyper-V VMs (Svr2008) on a Dell PE T410 server with 24GB of RAM (1333MHz) & dual quad-core, and both VMs (only their C: drives) are on a single RAID5 array. All clients connect via 1Gb ethernet. The 2nd VM is SBS2008 with 9GB RAM (& all SBS dbs & company data are on a separate RAID5 array), & 3GB RAM for the Svr2008 hypervisor. I've given the Sage/MSSQL VM all the RAM I can (12GB) & SQL RAM caching (~8GB, never exceeds ~7.5GB, eg. entire db can now be cached in RAM) and that's helped significantly. Upgrading the Hypervisor to Svr2012 is an obvious step, but probably not a dramatic improvement? What about an SSD for this Sage/SQL VM (VM = 100GB, <10GB for the actual live DB) ? Can SSDs be put into the SAS hot-swap bays? Or will I have to use the mobo SATA(3Gbps?) ports, or PCI-E SSD card? Should SSDs be RAIDed for this situation? Or is SSD's higher reliability offsetting the need for RAID1/5/10? (I have nightly full disk backups) New territory for me, would appreciate some feedback. Thanks, Anthony.

  Read the article

• snort analysis of wireshark capture

  - by Ben Voigt

  I'm trying to identify trouble users on our network. ntop identifies high traffic and high connection users, but malware doesn't always need high bandwidth to really mess things up. So I am trying to do offline analysis with snort (don't want to burden the router with inline analysis of 20 Mbps traffic). Apparently snort provides a -r option for this purpose, but I can't get the analysis to run. The analysis system is gentoo, amd64, in case that makes any difference. I've already used oinkmaster to download the latest IDS signatures. But when I try to run snort, I keep getting the following error: % snort -V ,,_ -*> Snort! <*- o" )~ Version 2.9.0.3 IPv6 GRE (Build 98) x86_64-linux '''' By Martin Roesch & The Snort Team: http://www.snort.org/snort/snort-team Copyright (C) 1998-2010 Sourcefire, Inc., et al. Using libpcap version 1.1.1 Using PCRE version: 8.11 2010-12-10 Using ZLIB version: 1.2.5 %> snort -v -r jan21-for-snort.cap -c /etc/snort/snort.conf -l ~/snortlog/ (snip) 273 out of 1024 flowbits in use. [ Port Based Pattern Matching Memory ] +- [ Aho-Corasick Summary ] ------------------------------------- | Storage Format : Full-Q | Finite Automaton : DFA | Alphabet Size : 256 Chars | Sizeof State : Variable (1,2,4 bytes) | Instances : 314 | 1 byte states : 304 | 2 byte states : 10 | 4 byte states : 0 | Characters : 69371 | States : 58631 | Transitions : 3471623 | State Density : 23.1% | Patterns : 3020 | Match States : 2934 | Memory (MB) : 29.66 | Patterns : 0.36 | Match Lists : 0.77 | DFA | 1 byte states : 1.37 | 2 byte states : 26.59 | 4 byte states : 0.00 +---------------------------------------------------------------- [ Number of patterns truncated to 20 bytes: 563 ] ERROR: Can't find pcap DAQ! Fatal Error, Quitting.. net-libs/daq is installed, but I don't even want to capture traffic, I just want to process the capture file. What configuration options should I be setting/unsetting in order to do offline analysis instead of real-time capture?

  Read the article

• Gmail and FB is not rendering properly in Firefox

  - by Andy

  I am unable read Gmail in my Firefox browser on my laptop. However, there are no problems when I try to access Gmail on my office desktop. In fact, Gmail renders fine on IE on both computers. Things I have tried: Uninstalling and reinstalling Firefox. Using Firefox 3.6.26 and Firefox 10; same problem. Clearing the cache. But all to no avail. For starters: My background image does not get loaded. It says "Oops. Your selected image failed to load". The buttons for the new look do not get rendered, but when I do a mouse-over I see text which helps me navigate. When I try to read a message, I see the subject line and I see the reply / forward box. The message body does not get rendered, it seems like a styling error. Check this screenshot where the icons in the GMail new look are not rendered properly Check this screenshot where even facebook is not getting rendered properly EDIT: 25th Feb 2012 GMAIL is getting rendered fine in the old look

  Read the article

• New Computer freezing up at random

  - by Benjamin Frost

  Since I built my system about 4 weeks ago I'v been getting random freezes, Sometimes it can happen directly after startup and sometimes it wont freeze up for 3-4 days of 24/7 running. It seems to be happening under all stress loads but mainly when the CPU is under 10% load. It doesn't give me a BSOD or anything, it simply just freezes and repeats the last sound before the freeze until I shut it down by the power button. I'v re-seated everything in the system except the CPU, Cleaned the RAM sockets and gold fittings. None of the components have been clocked above their factory settings as of yet, don't want to overclock them until I sort out these freezes. Temps are all well under the rated max temps, the highest the temps have been are below CPU: Low load: 16-21°C Full Load (100%) 40-43°C *(From HWMonitor by CPUID) GPU 1: Low Load: 25-30°C Full Load (100%): 45-50°C GPU 2: Low Load: 23-27°C Full Load (100%): 45-50°C *(GPU Temps from Catalyst Control Center) General Case temps Rear: 18-20°C Mid: 20-21°C Front (HDD/SSD Bays): 14-19°C (Case temps may be a little off as it's from the Kaze master pro fan controller) I have Un-installed EVERY driver for Motherboard, GPU & Soundcard and Re-installed twice. Windows is all up to date. To date i'v tried the following Running Memtest for 24 hrs straight, No errors Running Memtest on each individual RAM modules, No errors Reseated everything except the CPU Cleaned DIMM Sockets and Gold inputs Tested the Graphics cards 1 at a time Re-arranged all the SATA devices to run on Chipset controlled ports Re-installing all drivers OS: Win7 Professional 64bit Motherboard: ASRock X79 Extreme9 CPU: i7 3930k 3.2GHz GPU: Sapphire 7950 OC Edition V2 (2 card Crossfire) RAM: G.Skill Ripjaws Z F3-17000CL11Q-16GBZL 16GB (4x4GB) DDR3 Boot Drive: OCZ Agility 4 128GB Data Drive 1: Western Digital Black 2TB Data Drive 2: Western Digital Black 2TB Data Drive 3: Western Digital Green 3TB Power Supply: Corsair AX1200 Gold

  Read the article

• mysql startup, shtudown and logging on osx

  - by Joelio

  Hi, I am trying to troubleshoot some mysql problems (I have a table I cant seem to delete or drop, it hangs forever) I have 10.5.8 osx, I dont remember how/if I installed mysql, here is what I know: it automatically starts on boot the process looks like this: /usr/local/mysql/libexec/mysqld --basedir=/usr/local/mysql --datadir=/usr/local/mysql/var --pid-file=/usr/local/mysql/var/Joels-New-Pro.local.pid _mysql 96 0.0 0.0 75884 684 ?? Ss Sat06PM 0:00.02 /bin/sh /usr/local/mysql/bin/mysqld_safe when I run: /usr/local/mysql/libexec/mysqld --verbose --help it says: /usr/local/mysql/libexec/mysqld Ver 5.0.45 for apple-darwin9.1.0 on i686 (Source distribution) it seems to use my.cnf from /etc/my.cnf Now here are my questions: I dont see anything in the startupitems that remotely looks like mysql ls /Library/StartupItems/ BRESINKx86Monitoring ChmodBPF HP IO HP Trap Monitor Parallels ParallelsTransporter 1.) So how does it startup automatically? 2.) How do I start & stop this type of installation? Also, looking at the config, the logs have no values: /usr/local/mysql/libexec/mysqld --verbose --help|grep '^log' log (No default value) log-bin (No default value) log-bin-index (No default value) log-bin-trust-function-creators FALSE log-bin-trust-routine-creators FALSE log-error log-isam myisam.log log-queries-not-using-indexes FALSE log-short-format FALSE log-slave-updates FALSE log-slow-admin-statements FALSE log-slow-queries (No default value) log-tc tc.log log-tc-size 24576 log-update (No default value) log-warnings 1 3.) Does that mean there is no logging enabled in mysetup? thanks in advance! Joel

  Read the article

• Windows 8 auto-hibernate from sleep not working on Retina MacBook Pro

  - by frenchglen

  I have a similar question to this one. Only my context is the 15" Retina MacBook Pro - and Windows 8. I have just the original Mac OS X Mountain Lion on there, then Windows 8 via Bootcamp. no rEFIt installed. (I just press ALT every time I restart windows, actually as a security measure to stop tech-unsavvy thugs, who, if the laptop is stolen, think it's only a mac and don't discover my Windows as quickly as they would've, and by that time I remotely activate various anti-theft mac apps and nab them that way). SO: like the related question asks, why isn't it behaving like it should? The Windows 7 FAQ states: Will sleep eventually drain my laptop battery? If your laptop battery charge gets critically low while the computer is asleep, Windows automatically puts the laptop into hibernation mode. But this is just not happening - on my rMBP Windows 8. It seems EVERY time I set the laptop to sleep (when it reaches 10%), then arriving home and plugging it in and hoping to simply resume my work, it does NOT save the session to disk and I lose ALL my work. Who's fault is it? Win 8's (a bug, grr)? Or Apple's EFI system (maybe fixable via editing EFI options/do I have to install refit to make it work perhaps?) Or maybe changing windows power options can somehow fix the problem? Thanks for your help.

  Read the article

• WS2008 NTP - Using time.windows.com,0x9 - Time always skewed forwards

  - by David

  I have a domain controller configured to use time.windows.com (with 0x09 flags set). I've noticed that frequently the systems' clock is fast - it varies from 10 minutes to even 45 minutes. I always have to keep resetting the system date/time back to what it should be. When I run "w32tm /query /source" it tells me it's using time.windows.com, and obviously I trust Microsoft not to serve incorrect times, but why is my server's clock fast? EDIT: There are a few Time-Service events in the System log: Event ID: 142 Message: The time service has stopped advertising as a time source because the local clock is not synchronized. Event ID: 139 Message: The time service has started advertising as a time source. These two messages appear in pairs every hour or so. Event 142 appears 14 to 16 minutes after 139 appears. Going back a few months, these events appear: Event ID: 35 Message: The time service is now synchronizing the system time with the time source time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123-65.55.21.21:123). Event ID: 37 Message: The time provider NtpClient is currently receiving valid time data from time.windows.com,0x9 (ntp.m|0x9|0.0.0.0:123-65.55.21.21:123). Event ID: 47 Message: Time Provider NtpClient: No valid response has been received from manually configured peer time.windows.com,0x9 after 8 attempts to contact it. This peer will be discarded as a time source and NtpClient will attempt to discover a new peer with this DNS name. The error was: The time sample was rejected because: The peer is not synchronized, or it has been too long since the peer's last synchronization. These three events only appear once in the log, back in October.

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing. EDIT: If I currently have been trying: sudo route flush sudo route add default 192.168.19.1 This gets everything to work for about a minute. But after such minute it "forgets" the routing to WiFi while retaining LAN's (en0) routing. If I unplug and replug my LAN (en0) cable, the process works for another minute.

  Read the article

• ASUS N56VZ-S4209P Screen saver, Screen dimming,sleep/hibernation mode not working according to power management settings

  - by Alto Roos

  I have a problem with my ASUS N56VZ-S4209P(Win8, I7-3630QM) laptop. If I use the fn+f7 command to turn off the screen it turns on by itself after a few seconds (the time varies between 1-10 seconds). In addition to this my screensaver doesn't activate at all and the laptop doesn't dim its screen after X minutes or goes into sleep/hibernation mode as specified in the power options when plugged in or on battery. As far as my knowledge goes it's not caused by the mouse or track pad at all since I can unplug my mouse and disable the track pad but the problem persist. I presume this is caused by the same problem? Does anyone know of a fix for this problem? It would be greatly appreciated. . . . I seem to have found a solution to the problem related to the screen that turns itself on again. The Power4Gear application has a setting which enables you to turn a "Presentation mode" "On" and "Off", if that setting is "Off" then it doesn't turn the screen on without any human interaction. Thus that part of the problem is fixed.

  Read the article

• Bacula v5.0.2 Windows Installation Issues

  - by JohnyD

  First off, I am very new to Bacula but I'm very intriqued from what I've read. I'm looking to set up Bacula 5.0.2 on a Windows 2008 R2 server. I've run the installer and at the end it asks me to configure DIR name, DIR password, DIR Address. Windows documentation is somewhat hard to come by and I'm not certain what exactly I'm supposed to enter here. Do I need to create a local account that matches this info? Will the installation process create the account for me? Will this be the account that handles the FD daemon/service? I'm also not certain if Address means network location or local direcory. I apologize for my ignorance. Currently I'm trying to use the following information: Name: john pass: john address: thin1 (server name although I have also tried thin1.fqdm.local and 10.0.0.104) This info allows for the installer to complete successfully. However, when I run the BAT it hangs at, "Connecting to Director thin1:9101". The Bacula File Service is currently running under the local system account. What am I doing wrong? What do I have yet to do? Once I get this working properly I assume I will need to install clients on all my Windows boxes? Also, this is a 64-bit cpu but I am installing the 32-bit client. Are there any issues with this? Should I be using the 32-bit client? Thanks very much for the help.

  Read the article

• Convert raw IMAP server data into local folders, then upload partial dataset to new IMAP server?

  - by Manca Weeks

  I am transitioning a company with about 30 IMAP accounts, loaded with data (about 77GB total), to a new email host. The majority of the data will be converted into a local archive and distributed to the company computers as a static reference data set. The server side folders the users absolutely cannot do without being on the server will be uploaded back to the new server. I used Mac OS X Mail (Snow Leopard 10.6.6) to download the content. I notice some messages have the name [xxx].partial.emlx, which leads me to believe they have not been downloaded all the way. I have root access to the mail server data and could download the IMAP server data via FTP. I am not sure what utility to use to convert that data to local Mail.app mailboxes. Furthermore, I would appreciate any input on the best way to upload a portion of the data to the new server (GoDaddy), preserving the original dates of the messages. edit OK - forget the raw server data. I found a script that apparently does pretty good archiving IMAP folders to local mbx files. My main quest now is to batch upload a mailbox hierarchy to the new IMAP server without having to start-stop and deal with similar issues. Anyone know of a utility (hopefully for OS X, but if not, I'll fire up my XP virtual system...) that would be capable of this? Thanks, M

  Read the article

• Unix Permissions issue with users belonging to the same group accessing a folder

  - by TK Kocheran

  I have a folder I'd really like to allow another user on this machine access to. I'm using mt-daapd to serve music to the network, so I'd like to enable the mt-daapd user to access my Music directory, /home/rfkrocktk/Music. The master user is rfkrocktk obviously. I've tried to set all of my permissions properly on the directory, but the mt-daapd user can't acces the files. I created a group called media-users and added both rfkrocktk and mt-daapd to it in order to give mt-daapd permission to simply read all of the files in that directory and subdirectories. If I run id on each of my users, here's what's displayed: $ id rfkrocktk > uid=1000(rfkrocktk) gid=1000(rfkrocktk) groups=1000(rfkrocktk),4(adm),20(dialout),24(cdrom),29(audio),46(plugdev),104(lpadmin),115(admin),120(sambashare),124(vboxusers),1001(jupiter),2002(media-users) $ id mt-daapd > uid=123(mt-daapd) gid=65534(nogroup) groups=65534(nogroup),2002(media-users) It definitely seems that both users are a part of the media-users group, so what could be going wrong? If I run ls -l on the actual Music directory to see its permissions, here's the output: drwxr-Sr-- 201 rfkrocktk media-users 12288 2011-01-13 12:26 Music If I run ls -l on the Music directory to get its children, here's the output: drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-12-20 15:31 2DBoy drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-05-25 12:50 ABBA drwxr-Sr-- 3 rfkrocktk media-users 4096 2009-12-28 15:19 Access Denied drwxr-Sr-- 10 rfkrocktk media-users 4096 2009-12-28 15:19 AC-DC drwxr-Sr-- 3 rfkrocktk media-users 4096 2009-12-28 15:19 Aerosmith drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-06-04 10:45 A Flock of Seagulls drwxr-Sr-- 4 rfkrocktk media-users 4096 2010-05-28 18:13 Alestorm drwxr-Sr-- 3 rfkrocktk media-users 4096 2010-06-22 23:29 Amon Amarth drwxr-Sr-- 5 rfkrocktk media-users 4096 2009-12-28 15:19 Anberlin ... From this, it would seem that I should be able to access the folders from mt-daapd, but I can't. Running sudo -i -u mt-daapd ls -l /home/rfkrocktk/Music displays nothing, indicating to me that for whatever reason, mt-daapd doesn't have access to read the folder. What am I doing wrong?

  Read the article

• Plesk + Apache + PHP (FastCGI): Constant session permissions problems, conflicts between HTTP / HTTPS

  - by Hans Engel

  I've just moved a collection of sites over to a brand-new server, running Apache 2.2.3, PHP 5.3, and Plesk 10.1.1. I am having problems with file permissions on PHP sessions, which are being stored in /var/lib/php/session. I originally set the permissions like so for this folder: drwxrwx--- 2 apache psacln 8192 Mar 22 23:25 session This worked fine, for HTTP sessions. Files were being saved in that folder with these permissions: -rw------- 1 client1 psacln 0 Mar 22 23:24 sess_507... -rw------- 1 client2 psacln 0 Mar 22 23:25 sess_8o1... The problem, however, is that PHP scripts accessed via HTTPS do not seem to be run by the same client1 or client2 user. I deleted files in the session directory and accessed a login page via HTTPS to see how sessions were being saved when initiated via this protocol: -rw------- 1 apache apache 0 Mar 22 23:25 sess_507... So, for whatever reason, sessions initiated by clients browsing with HTTPS were being saved by apache:apache, while sessions from HTTP clients were saved with someclient:psacln. What I'd like to ask: How can I avoid this problem with session permissions? When sessions are created via unencrypted HTTP and a client visits an HTTPS portion of the site, permission errors are shown, since apache:apache tries to access the session save created by someclient:psacln. The converse is also true. Can I change the user which runs the Apache HTTPS server, via Plesk or the command line? If not, can I have PHP sessions save with rw-rw---- permissions, and then add apache to the psacln group? Any other suggestions on how to fix this issue?

  Read the article

• Sendmail Sends but never Delivers

  - by Jeremy

  I have tried 10 different emails hosted at Google, Yahoo!, GoDaddy, and some that are privately hosted, and each time I get the following errors. I have blocked sensitive information, but you will be able to see the errors. Feb 16 17:06:50 xxxxx sendmail[31824]: o1GM6ovJ031824: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30054, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GM6oJo031825 Message accepted for delivery) Feb 16 16:54:19 xxxxx sendmail[31625]: o1GLsJPP031625: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30097, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GLsJah031626 Message accepted for delivery) Feb 17 09:05:52 xxxxx sm-mta[10620]: o1H6Z3jM005734: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=07:30:49, xdelay=01:15:36, mailer=esmtp, pri=571331, relay=aspmx3.googlemail.com. [209.85.222.4], dsn=4.0.0, stat=Deferred: Connection timed out with aspmx3.googlemail.com. Feb 17 10:35:23 xxxxx sm-mta[12828]: o1HEZwn8011833: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=00:59:25, xdelay=00:12:36, mailer=esmtp, pri=300353, relay=aln-mailrelay.att.net. [12.102.252.75], dsn=4.0.0, stat=Deferred: Connection timed out with aln-mailrelay.att.net. If you take a look, they all send, but then (HOURS later) I get an error "stat=Deferred: Connection timed out with {server}". I'm at my wits end, because I use this same setup on each of my servers, and they all work.

  Read the article

• Broken Creative DTT3500 Digital

  - by djechelon

  Hello, many years ago I bought a Creative DTT3500 Digital surround speakers system. It's been a while since my home theatre started behaving strange. During the past 6 months, I have noticed that the amplifier needed some time before correctly playing digital audio. Until a couple of weeks ago, it needed up to 5 minutes of very noisy "warm up" before playing an "almost" clear audio. Today, I found that even using the analog input (completely disabling digital inputs) the noise persists. Powering off and on the speakers doesn't work. Now, it's reasonable that after almost 10 years, the amplifier got broken. My problem is that I can't simply replace the speakers with another kit from another brand, since 2 speakers in my room are placed in the back wall, with coaxial cables going under the floor but not completely inside a single tube. I mean, I have coaxial extension cables starting from the DTT3500 amplifier, going into the wall, then under the floor in a plastic cable tube, then exiting the tube (still under the floor), connecting to the male coaxial connector of the original cable supplied by Creative, and continuing up to the point close to my bed where the speakers are. I could replace the speakers **only as soon as the new speakers have the same coaxial to bi-polar cables that Creative ships with DTT3500 Another option might be "repairing the amplifier", but I don't know if it's feasible, what should I or a technician look for in the amplifier, and how much would it cost (is it worth to repair or buy a new kit considering the problem above? What do you suggest me to do, basing on the above observation? Thank you.

  Read the article

• Multiple IPv6 addresses being assigned to single interface

  - by Steven Copestake

  I'm configuring a DHCP scope for IPv6, however all my clients are getting 2 or more IPv6 addresses assigned to the interface. I'm using fda8:6c3:ce53:a890:/64 as the prefix. The scope is on a machine running Windows Server 2008 R2 however I'm looking to roll it out on Server 2012 as well. My clients are getting the following: IPv6 Address. . . . . . . . . . . : 1024::1492:9288:7357:7d30(Preferred) IPv6 Address. . . . . . . . . . . : fda8:6c3:ce53:a890::1(Preferred) IPv6 Address. . . . . . . . . . . : fda8:6c3:ce53:a890:1492:9288:7357:7d30(Pr rred) Link-local IPv6 Address . . . . . : fe80::1492:9288:7357:7d30%10(Preferred) In this example there's no DHCP scope and the machine has a static IP of fda8:6c3:ce53:a890::1. With this in mind where are the 1024 address and the fda8:6c3:ce53:a890:1492:9288:7357:7d30 address coming from?

  Read the article

• Mac Mini server (10.6) behind router with FQDN hostname

  - by thechriskelley

  I have a Mac Mini running Mac OS 10.6.6 Server that will be part of a local network, and a static IP from my ISP. I'd like to set up DNS for the Mini with a FQDN as the hostname (example.com) properly. The Mini is behind a router (Apple Airport Extreme) and is given a private, static IP address. I can't assign it the public static IP directly because it's behind a router with DHCP/NAT for other machines on the local net. My end goal here is for services to resolve to the server properly from outside and inside the local network to users via example.com (and subdomains like mail.example.com, www.example.com), which will point to the public static IP assigned to the router. Will DNS work/resolve properly (for mail services and other subdomains) if it has a private ip address, but the necessary services are forwarded properly through NAT? I'm open to any (hopefully better) suggestions, as my current setup doesn't seem like it's the best way. Currently, more hardware or another public static IP is not possible. With the current setup, it seems as though one static IP is not necessary anyway. Thanks in advance for any insight.

  Read the article

< Previous Page | 855 856 857 858 859 860 861 862 863 864 865 866  | Next Page >